Remove the spa cover and let the water temperature cool down to 40°C (104°F). I CE2 = Freeze protection. S Y M P T O M Spa Inoperative MESSAGE FLO HILI ICE LS SS CP REL HC P1/P2/P3 F1/F2/F3/F4 BUS * These procedures should only be performed by persons familiar Check for proper spa water level and ensure pump is primed. http://prcflow.com/error-code/vpn-error-codes.html
Contact qualified service technician. When I 10/25/2016 10/25/2016 billyjr1961 I would like to talk with a repair person regarding my 10/25/2016 10/25/2016 rickspaserv Where can i find wiring manual for a sundance spa with a if the heater is not working does that also affect the blower which causes the bubbles?Customer : The water temperture is probably around 20 degrees its never been turned off it PSoH Pressure switch open with high pump. http://www.justanswer.com/pool-and-spa/7nzmu-hi-vita-spa-code-ice-pump-circulate.html
Other issues that can cause these error codes one or more of the service valves is not open up all the way. Spa has shut down. Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Std: Spa operating in Standard Mode.
These error codes are caused by a variety of reasons. SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational.SESH = Sensor short, nonfunctional. Gecko Spa Pack Error Codes drops.
Heater is deactivated SN Sensor failure SN1 Hi-limit sensor failure SN2 Temp sensor failure SS=0;SS=S; Multiple causes; open sensors, bad connection to panel, improper voltage, etc. Balboa Hot Tub Error Codes FLO* = Flow Switch (heater is deactivated. Customer : But how do I get the temperture up? https://spacare.com/spasideerrorcodes.aspx System will restart when temp.
The Spa or Hot Tub Panel Displays: HH, OOH, OH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights At least one of the sensors has detected water temperatures of Balboa Spa Control Manual This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally. COL = Cool condition. system error FN-ER: Fan failure FB-ER: Fiber optic failure SC-ER: System learning failure Hurricane Error Codes PS: Flow/pressure switch fail SH: Shorted sensor OP: Open Sensor Degrees LO: Temp below 60
OHH = Overheat. http://www.spadepot.com/spa-error-codes.htm ICE = Freeze protection. Hot Tub Error Codes No action is necessary.I CE2 = Freeze protection. Vita Spa Error Codes The system returned: (22) Invalid argument The remote host or network may be down.
hot = Overheating, water over 112° F. have a peek at these guys Heater is shut down, but other spa functions run normally. The Spa or Hot Tub Panel Displays: dr, dry This indicates that there is not enough water in the heater. We got one lid 10/23/2016 10/23/2016 waymore3 X Ask a Pool and Spa Expert Get a Professional Answer. 100% Satisfaction Guaranteed. 29 Pool and Spa Experts are Online Now Type Your Marquis Spa Error Codes
no heater light is on. 2 months ago it started to make a buz noise at each cycle of every 4 hours now it does not make that noise any longerpoolguy810 If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open If alternating with temp, may be temporary condition. check over here Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 =
The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue. Coleman Spa Error Codes PAGE 20 Previous page Next page 1...222324252627282930 Related Manuals for Vita Spa xStream Hot Tub Vita Spa LX series Owner's Manual Vita spas (12 pages) Hot Tub Vita Spa Spa Water temperature has reached 118°F.
Do not enter the water.FL = Flow. Check for low water level and ensure pump is primed. In rare cases (usually warmer climates), the circulation pump may also cause overheating. Spa Command Panel Instructions Entire system is disabled.
SESH : Sensor short, nonfunctional. Sn2 = Nonfunctional temperature sensor. IC, ICE, ICE2 Freeze Condition detected; Warm up procedure begins. this content Flo: flow/pressure switch error Cool: Water temp 20 degrees below set point ICE: Potential freeze condition Sn1: Hi-limit sensor failure Sn3: Temp sensor malfunction Sna: Sensor A fail Snb: Sensor B
One sensor has detected 110º F. Hold = Panel sensors have been pressed too many times in a short period of time.HOT = Circuit Board temperature has exceeded acceptable limit.ICE = Freeze protection. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Heater deactivated Sn2 Temperature sensor fault Sn3 Temp sensor failure SnS Sensors out of balance.
If alternating with temp, may be temporary condition.