Welcome to VTC talk Forums. Check the device indicated in this alarm and confirm that the device registration details in Cisco Unified CM Administration are accurate. The device did not provide an Authorization header after Unified CM challenged with a 401 Unauthorized message. If the problem still persists, restart the TFTP service and Cisco CallManager service. 15 CallManagerRestart - A device restart was initiated from Unified CM, either due to an explicit command from
Reason Code - Enum Definitions Enum Definitions - LocalApplicationID Value Definition 100 CallManager Enum Definitions - RemoteApplicationID Value Definition 100 CallManager Error Message CCM_CALLMANAGER-CALLMANAGER-1-CMVersionMismatch : One or more Unified CM nodes NM_CALLERR_MEDIA0x81000101Invalid channel/media types. Can anyone else get it? __________________ George Boone Founder of VTCTalk.com New project: VDOStream.com I'm still alive! This action is an attempt to stop malicious attacks on Unified CM or to ward off excessive CPU usage. click to read more
Please type your message and try again. For trunks, this alarm should only occur when a system administrator has made a configuration change such as resetting the H.323 trunk. Possible causes include device power outage, network power outage, network configuration error, network delay, packet drops, and packet corruption. No action is required if this event was issued as a result of a normal device rehome.
Note that this alarm describes the readiness of Unified CM to communicate with the indicated device but does not provide information about the state of the H.323 device (whether it is Why cast an A-lister for Groot? If status shows 2, then replication is working. Vidyo Support Verify that the device is configured with digest credentials and is able to respond to 401 challenges with an Authorization header.
If the reason is ConfigurationMismatch, go to the Device Configuration page in Cisco Unified CM Administration, make a change to the Description field for this device, click Save, then reset the See above link to look up what the error codes mean on your VC units.. Apple Info Site Map Hot News RSS Feeds Contact Us Copyright © Apple Inc. http://www.vidyo.com/services-support/technical-support/product-documentation/ Possible causes include device power outage, network power outage, network configuration error, network delay, packet drops, and packet corruption.
Check the Security profile of the indicated device and verify that the Device Security Mode is set to either Authenticated or Encrypted. Vidyo Knowledge Center When an individual device exceeds the number configured in that service parameter, Unified CM closes the TCP connection to the device; automatic reregistration generally follows. Also, refer to the reason code definitions in the alarm for recommended actions. In the case of a device rehoming to the primary Unified CM node, watch for a successful registration of the device on the primary node.
Reason Code - Enum Definitions Enum Definitions - PerfMonObjType Value Definition 1 Cisco CallManager 2 Cisco Phones 3 Cisco Lines 4 Cisco H323 5 Cisco MGCP Gateway 6 Cisco MOH Device https://supportforums.cisco.com/discussion/10482811/get-error-message-when-scheduling-video-conferencing-meeting-place The alarm could also indicate a device misconfiguration, database error, or an illegal/unknown device trying to attempt a connection. Vidyo Not Showing Video Also, confirm that database replication is working. Zoom Error Code 5003 If status shows 2, then replication is working.
Check the REGISTER message for any of these issues and if you find one, correct the issue. 12 SCCPDeviceThrottling - (SCCP only) The indicated SCCP device exceeded the maximum number of If the database replication status is good, reset the device. Coding Standard - haphazard application What is an instant of time? If the device does not re-register within 5 minutes, confirm that the device is powered-up and confirm that network connectivity exists between the device and Unified CM. 19 EMLoginLogout - The Zoom Error Code 2008
Dev centers Windows Office Visual Studio Microsoft Azure More... If this alarm persists, verify that the appropriate number of lines has been configured on the device, and that the appropriate directory numbers have been configured. Warrior You can also get this in the TANDBERG endpoints MXP http://yourcodecIP/causecd.htm classic systems: under the diagnostics section Sean Sean Lessman View Public Profile Send a private message to Sean NM_E_CHANNEL_ALREADY_EXISTS0X81000201Data channel already exists.
For H.323 clients, this alarm occurrence is normal on lower-priority Unified CM nodes when a high-priority Unified CM node starts. Vidyo Camera Not Working Also, refer to the reason code descriptions in this alarm for additional recommended actions. If the device is a third-party phone, confirm that the endpoint is sending a properly formatted REGISTER message. 4 AuthenticationError - The digest User ID or password sent from the phone
If this device continues to unregister with this reason code, go to the Device Configuration page in Unified CM Administration for the device indicated in this alarm and click Save. Verify that the X.509 Subject Name field has the appropriate information. Follow me at http://twitter.com/georgeaboone George View Public Profile Send a private message to George Visit George's homepage! Vidyo Firewall Ports NM_CALLERR_AUDIO0x81000109Audio connection failed.
Verify that the TFTP server is reachable from the device. How much more than my mortgage should I charge for rent? NM_CALLERR_ALREADY_CALLING0x810001FDAlready calling this person. Warrior New Zealand Warrior View Public Profile Send a private message to New Zealand Warrior Find More Posts by New Zealand Warrior 09-28-2004 #2 George VTC Professional
No action is necessary; the device will re-register automatically. 14 ConfigurationMismatch (SIP only) The configuration on the device does not match the configuration in Unified CM. All rights reserved. To correct this problem, configure this device in Unified CM Administration. 3 DatabaseConfigurationError - The device is not configured in the Unified CM Administration database and auto-registration is either not supported If the problem still persists, restart the TFTP service and the Cisco CallManager service from the Control Center - Feature Services web page. 6 MaxLinesExceeded - The phone is attempting to
If the node was taken out of service intentionally, bring the node back into service. Verify that the TFTP service is activated. How can i notice when someone from conference hangs up?0How can notify other user while video calling oovoo sdk0ooVooAVChatDelegate is not called when a participant joins in swift Hot Network Questions This action is an attempt to stop malicious attacks on Unified CM or to ward off excessive CPU usage. 13 KeepAliveTimeout - A KeepAlive message was not received.